Q: I am using a  Miracle Oil Additive that is supposed to eliminate wear on start up so why would I need to install Insta-Lube System?

A: There are a lot of oil additives that claim to eliminate some wear by depositing a film of lubricant on the bearings surfaces.

But none of this will pressurize and adjust the hydraulic valve lifters or positively separate bearing surfaces with pressurized oil like the Insta-Lube Pre lube system.   

Q: I have a 1956 Cadillac Coupe Deville and want to keep the same engine appearance; can the tank be mounted remotely?

A: Yes the kit will work on your Caddy; the hose is long enough to place the tank and valve out of site so everything looks stock.

Q: I am rebuilding a 350 Chevy and will install the kit; can the tank be filled with oil ready to prelube the very first startup?

A: Yes the Accumulator can be filled with oil ready to pre lube the engine for the first time. Just use the air valve located toward the top of the tank to add compressed air to build a back pressure for first operation of the new engine.

A lot of experts say the first startup after rebuild or new engine, creates an exceptional amount of the total bearing wear, and can be avoided completely with the Insta-Lube Kit installed.

Q: I have a Winnebago motor home with a 440 CID V8 Engine will the preluber work on this engine as well as my four-cylinder Nissan?

A: Yes the pre Oil kit will work on all internal combustion engines.

Q: Its a well-known fact that a great deal of Motor Bearing Wear  is at startup, so why dont the manufactures address the problem?

A: Thats a good question and a lot of people ask it. It isn't a secret and yet only a few engine builders incorporate a pre lube system in their design.

One thing for sure, if all engines were pre lubed before startup, there would be a lot fewer new ones made.

Q: Will it work on my motor home?

A: All Cars, trucks, suvs, vans, motor homes, boats, tractors, stationary engines or any other engine using a pressurized oil system will benefit the same with the Insta-Lube System.

Q: How good is the Insta-Lube Pre Lube System in cold weather?

A: This is an area that is especially important as a lot of wear takes place on cold startups, our customers in Iceland really appreciate the Insta-Lube kits.

By installing the Insta-Lube pre-oil Kit you eliminate most of this bearing wear and prolong the life of your engine.

Q: How difficult is the Insta-Lube Pre Lube kit to install?

A: There are 3 easy steps to install the Insta-Lube Kit

1. Bolt on the mounting bracket with 2 bolts or self-tapping screws.

2. Connect  the hydraulic hose between engine and storage tank.

3. Connect 12 volt positive wire to selected fuse and solenoid valve.

Q: Will the Pre Lube kit be any help in preventive maintenance for my cab?

A: The Insta-Lube System will benefit all engines, some more than others.

Since you have multiple startups daily it will make a substantial reduction in overall engine wear.

Q: Will installing the kit void my engine warranty?

A: Many of our customers are new car or truck owners and have had no problem with warranty questions.

It should be the same as adding oil cooler or remote filter but to be sure about your vehicle, consult the manufacturer.

Q: After installing the Insta-Lube Kit will there be less emission?

A: Yes, the pre-adjusted hydraulic valve Lifters will have the engine tuned for maximum efficiency and less emissions.

However the primary benefit to the engine is eliminating the wear to the Main bearings, Rod bearings, Camshaft bearings, Pistons, Piston Rings, and Wrist pens, Cylinder Walls, Hydraulic Valve Lifters, Timing Gears, and Timing Chains during startup.

Q: I have a 1951 Pontiac that uses a 6-volt electrical system will the pre-luber work on it?

A: yes, 6 volt 12 volt or 24-volt systems will work.

Q: Is the oil that is stored in the accumulator tank filtered oil?

A: Yes, only pre-filtered oil from the engine oil gallery is stored for pre-lubing the engine the next time you turn the key on.

Marine Grade Solenoid Valve, Black Powder Coated Aluminum Storage Tank, 6 ft of 3/8 in Hydraulic Hose, Pipe Fittings, Mounting Bracket With SS Clamp, Wiring, Crimp Fittings, Fuse/Fuse Holder, Instructions and Warranty.

Complete Kit Only $179.95

Toll Free Order 1-866-323-6155

MotorPrelube
Box 29502 #89502
Las Vegas NV 89126
866-323-6155
Sales@motorprelube.com